100years_white-SM Banner-1
Special Report-HOME-E-1
facebook-main-A-1 twitter-icon-main-A-1 youtube-main-1 icon_taegutec-A-1 podomatic-A-1 sitemap_icon contactus_icon BuzzCuttzz_icon03 BriefCutzz-Icon-main-B-1

Products on Triple-T

SpadeRush-NAV SM-1
T-Clamp-Ultra Plus-NAV SM-A-1
TopSlot-3edge-NAV SM-NEW-C-1
TT7015 Life+-NAV SM-1
TT8080-NAV SM-1
TT7505-NAV SM-1
7515-NAV SM-1
T-Deep-Gundrill-heads-insert-NAV SM-1
ChaseAlu XEVT-A-NAV SM-1
TopDrill-DA-DK-MID SM-A-1
DR-DblMargin-NAV SM-1

TaeguTec New Product


Tough Materials Meet their Match with New SiAlON Grades

TC3020 and TC3030 New Ceramic Grades for High Temperature Alloy Machining

May 18, 2016 – The demand for cutting tools to increase productivity and cut the cost of machining high temperature alloys is always increasing, that is why TaeguTec has launched two new SiAlON ceramic grades - the TC3020 and TC3030 - that offer superior performance.

Both the TC3020 and TC3030 ceramic grades are suitable for high temperature alloy machining where difficult-to-cut materials such as Inconel, rene and titanium are used. These ceramic grades are characterized by their excellent toughness and anti-chipping capabilities making them the best choice for both interrupted and continuous machining.

With the introduction of both these grades, the Asian metalworking giant has gone a step further by supplying even more optimal solutions for machining high temperature alloys than its current whisker ceramic grade.

The new grades are available for insert lines in turning, milling and grooving applications.

The TC3020 is ideal for high temperature alloy machining and runs in the same conditions as the whisker ceramic grade. Its superior wear resistance is due to its high stability while it offers better flank and notch wear resistance compared to the competitor’s similar grade. Furthermore, the TC3020 has excellent high temperature strength and fracture toughness.

TC3020-ceramic-MID SM-A-1




The other new offering, the TC3030, is also created to handle high temperature alloys with the difference being that the grade’s extreme toughness enables it more for higher feed and heavier depth of cut machining and is suitable for scaling and roughing applications while offering excellent thermal shock resistance and thermal conductivity.

By combining silicon nitride and aluminum oxide, TaeguTec’s SiAlON grade offers incredible chemical stability in order to reduce notch wear in demanding operations and has the capability to run at 4-6 times the speed of conventional carbide inserts.

Product testing in real-world machining conditions demonstrated increases in productivity and tool life.

Related Articles

- TT7015 Life+ Turning Grade for Cast Iron

- TT7005 Life+ CVD Coating HS Cast Iron

- TT8080 Turning for High Temp. Alloys

- TT7505 Chips at the Hard, Tough

- TT7515 High-Speed, Roughing Cast Iron

- TT8105 Added to Life+

- Adding Life is a Plus with New Grade

- AW120 Ceramic Turning Grade

- TT2510 Milling Grade

- TT5515, TT5525 End Mill Grades

- TD810 PCD Hybrid Grade

While performing a continuous grooving operation on an engine casing made from Inconel 718, the TC3020 grade’s productivity increased by 40 percent over the competitor’s similar ceramic grade.

For an engine casing made from the same Inconel 718 with external interrupted turning and interrupted grooving operations, TaeguTec’s TC3030 increased tool life by 23 percent and 56 percent respectively.

The biggest improvement over the competition was on a rene 108 material, the TC3030 performed incredibly well on a face milling operation of a shroud workpiece when it increased tool life by 100 percent.

For more information concerning TaeguTec’s cutting tools and industrial products, or to locate a dealer nearest you, visit www.taegutec.com



New Product News

TC3020-TC3030-MID NAV LG-1

More New Product News

DuetBall ML-MID NAV SM-1 TT8080-MID NAV SM-1 ChaseMold RTMX-MID NAV SM-1
NPN-TopDrill-inch-MID-NAV SM-1 NPN-Typhoon-NAV SM-1 NPN-QR TQS 8mm-MID NAV SM-1
Bottom line


C2M 4NKT-NAV SM-1 Hardmill-NAV SM-1
CM Power-NAV SM-1 Life+-NAV SM-1
T-Burst-T-Clamp-NAV SM A-1 QR-Threading-NAV SM-1

Korea-Trans-1 한국어

Italy-Trans-16-1 Italiano

China-Trans-1 中文

Czech-Trans-16-1 Čeština

Brazil-Trans-16-1 Portuguęs

Ukraine-Trans-16-1 Русский

Argentina-Trans-16-1 Espaņol (AR)

Products on Triple-T

DR Flat bottom-TOP-NPA12_02-NAV SM-NEW-1
RhinoRush-DNUX-T-Holder-WNMX-NAV SM-NEW-1
NP-EH ChipBreaker-NAV SM-NEW-1
TwinRush-NAV SM-A-1
SR 100yrs-NAV SM-1
TTAPP intro-NAV SM-1
BuzzCutzz_NAV SM-1
Success Stories-NAV SM-1
RR-ML-ScrewClampingBB-NAV SM-1
T-Holder Combi Clamp-NAV SM-1
Splitter-NAV SM-1
ChaseMill APKT 1706-NAV SM-1
FineBall-expansion-NAV SM-1
DR 6mm-NAV SM-1
[Home] [News] [Photo Gallery] [TT-Plus] [New Products] [How To & Tips] [Events] [Contact Us] [Site Map]

TaeguTec is renowned for its specialist tungsten carbide cutting tools, tungsten powders, tungsten carbide rolls and industrial products. The specialist tooling engineers at TaeguTec are continually introducing innovative new methods of producing cutting tools for the metal cutting industry, to deliver some of the best cutting tool solutions to various market sectors such as the automotive, mold and die, aerospace and heavy industry sectors. For further information on TaeguTec products, please visit TaeguTec website www.taegutec.com

© 2016 TaeguTec LTD. Cutting Tools, Industrial Products, Tungsten Powders (TaeguTec.com) All Rights Reserved.